![]() ![]()
Therefore, to connect an RS-232 device (such as a CR1000) to a computer, you need to use a USB to RS-232 adapter, such as the 17394 converter. With the widespread adoption of USB, most computers sold now do not have an RS-232 port. #HL 340 USB SERIAL DRIVER XP SOFTWARE#The software driver sits between the hardware and the computer program you are using, and it must be installed and working correctly. To handle the packets and move data in and out of the program accessing the USB device, a software driver is needed. Data is wrapped up and transferred in packets. USB devices have high throughput, but they use a shared data bus. The USB provided smaller connectors and more data throughput than the serial and parallel interfaces it replaced. In 1996, the Universal Serial Bus (USB) standard was introduced as a replacement for the serial connector and other connector types that were typically found on the back of computers. Data practically flowed directly to and from the software that was accessing the serial port. ![]() Built-in RS-232 ports featured direct mapping to memory and worked at a high priority. The connector was reduced from a 25-pin connector to a 9-pin connector, but RS-232 ports remained present on every computer for many years. Apart from the parallel port, it was the primary means to connect an external device. In the old days of personal computers, one of the primary connections available was the RS-232 serial port. In this article, I’ll briefly discuss the origin of these issues and provide you with some suggestions for successfully handling them. Our customers frequently encounter issues with these adapters. Having DSR, CTS, RTS and DTR available can come in very handy, allowing for example, a VB based app to do I/O with the Picaxe.Have you had difficulty using a USB to RS-232 adapter to connect your RS-232 device to a computer? If so, you are not alone. All you have to do is solder in a header into an unpopulated header position on the board. These bring out ALL of the serial signals including DTR,RTS, DSR, CTS and RI. There are some CP2102 based USB to TTL adapters on EBay branded "BAITE". While I use these cheapies here on the bench with good results, my preference is still an FTDI based adapter. Some of these are known to be fakes and might not work. The only way you would not need to invert the data is if you get a USB to RS232 cable/adaptor, in which case the adapter will be sending RS232 level voltages to the Picaxe just like using an AXE026 serial cable. Any of these methods should give adequate results. or two NPN transistors or even two 2n7000 FETS. Inversion can be done with either a digital inverter chip such as an 74HC14 or equivalent. None of these can be programmed to invert the data ( required for Picaxe programming) so external inversion will be necessary. All can usually be made to work unless you happen to get a "fake" Prolific based adapter where the Bridge Chip is not a real Prolific Chip. #HL 340 USB SERIAL DRIVER XP DOWNLOAD#I have used the arduino one before but at 10€ + shipping it is almost as expensive as the Download have done extensive testing of most of the "cheap" USB to TTL adapters, including several different models of CP2102, Prolific, and CH340/341. ![]() One of the cheapest is this one from, where else, China: What are your experiences with these USB adapters? If I google a litle bit I find all kinds of USB to Serial/UART devices ranging from 2.5 USD up to infinity The circuit only draws a few miliamps, far less then 100 mA and runs on 5V so it should be perfectly happy with USB power. #HL 340 USB SERIAL DRIVER XP UPGRADE#One example is a project where I upgrade a old NES controller to send button events over USB to my PC where a application written in C# converts the serial data back to keystrokes. ![]() The Picaxe download cable is very nice but at 12£ it's quite expensive (compared to the low cost of a picaxe) it also, for a good reason, lacks the ability to power the picaxe. For some projects I need constant Picaxe to PC communication over USB. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |